9:07 ■I5G Practice 4a Load Families Sony Type Family Q TT Revit Families Practice Objective Load and add components. In this practice, you will load and create families for up coming practices in this guide. You will load components from the project folders custom library and create a new size. You will then create a new size for a system family. Finally, you will load a symbol from the Load Autodesk Family dialog box. Task 1-Load families. 1. Open the project Structural-Compnts.rvt from the practice files folder. 2. In the Insert tab>Load from Library panel, click Family). (Load 3. In the Load Family dialog box, navigate to the practice files Families folder and select the following families: ⚫ Angled-Footing.rfa Concrete-Rectangular-Column.rfa K-Series Bar Joist-Rod Web.rfa Click Open. 4. In the Specify Types dialog box, select K-Series Bar Joist-Rod Web.rfa from the Family list and then select 16K7 from the Types list as shown in Figure 4-17 and click OK. The other families do not have any type catalog available to choose sizes from. Denty S L W 14 55 ப 1664 70 75 5. Save the project. © 2022, ASCENT - Center for Technical Knowledge® Figure 4-17 AA platform.virdocs.com Calor 4-15 = > 9:10 AA ■I5G Q TT : Basic Sketching and Mocity Tools 13.Click(Modity) 14. Save the project Task 2-Rotate elements. 1. Select gnc line 1. 2. In the Modity Grids tab>Modity panel, click (Rctate) 3. Move the center of rotation by going to the Options Bar and clicking Place. Select the midpoint of column D1 as the center of rotation. 4. Specify the first ray of rotation by clicking on the A1 grid intersection 5. Specify the second ray of rotation to finish the rotation by selecting the midpoint of the column you moved 6 to the left. of grid line 1 earlier, as shown in Figure 5-55. Second ray of retation. selection First ray of rotation selection Center of rotation- 2022, ASCENT-Center for Technical Knowledge Page 239 Figure 5-55 platform.virdocs.com 5-39 9:11 !!! . 5G Q TT Autodesk Revit 2023 Structure Fundamentals 4. Select the intersection of the reference plane and grid line A, between grid lines 2 and 3, as shown in Figure 5-77. Reference line- Grid line A 5. Click A Figure 5-77 (Modify) to end the command. 6. Connect the arc foundation wall on grid line A.1 with the foundation wall on grid line A by going to the Modify tab> Modify panel and clicking (Trim/Extend to Corner). 7. Select the horizontal wall along grid line A on the left side of the arc, as shown in Figure 5-78. • Remember to select the side of the wall that you want to keep. Figure 5-78 5-52 ©2022, ASCENT-Center for Technical Knowledge® I r AA platform.virdocs.com = > 9:07 AA ■I5G Q TT : Revit Families 6. In the Type Properties dialog box, under Dimensions, set the Width to 2-0, as shown in Figure 4-19. Tree Fly Parametr Material des Senatural Materid Stricting Structand tha With Founder on Thi fak ind Fitn Faku Courete Cast in Place Concnt Boating Figure 4-19 You must have an internet connection to Uso the Load Autodesk Family method. This family is also provided in the practice les Families Tables folder 7. Click OK Click (Modify) Task 4. Add a detall family from Load Autodesk Family. 1. In the Insert tab>Load from Library panel, dick (Load Autodesk Family) 2. In the Load Autodesk Family dialog box, type Break line in the search field. Select the image of the table and chairs (as shown in Figure 4-20) and click Load Filler Covy Ay < 12 Detalle 00-Gene cat X List Cancel Figure 4-20 3. Save and close the project 2022, ASCENT-Center for Technical Knowledge Page 197 platform.virdocs.com 4-17 ( ☐ 9:11 ■I5G Autodesk Revit 2023 Structure Fundamentals 3. Hover the cursor over one of the foundation walls but do not select the wall. The blue alignment line should display on the inside of the wall and above the grid line, as shown in Figure 5-81. Alignment line. 5-54 Chain of walls or lines Figure 5-81 (A.1 4. Press <Tab> until all of the foundation walls are highlighted, meaning they are all selected, and click to offset the walls 4", as shown in Figure 5-82. New location of foundation walls Figure 5-82 5. Click R (Modify). 6. Save and close the model. ©2022, ASCENT - Center for Technical Knowledge® AA r platform.virdocs.com/n CVEN 1025 001 3 Credits - Autocad Introduction T Denver MAM CU IN THE CITY AutoCAD Civil Engineering Graphics and Computer Aided Design Homework Exercise 11: • Please complete the following problems from the text book. Perform the following practice problems in the Revit textbook and submit the saved file: Practice 4A, page 4-15 Practice 5A, page 5-20 • Practice 5B, page 5-37 Practice 5C, page 5-51 Submission Details: Submit to Canvas as a .rvt Textbook Chapters to Review: • Revit chapter 4 and 5 1