Register

Homework Help Question and Answers

Submit a new Query

Recent Homework Help Question & Answers


Question 26683

posted 1 years ago

Design a third order Butter worth stepped (Hi-Z Low-Z) low pass filter using microstriplines for a cutoff frequency of 2.4 GHz. Draw the final schematic in terms of normalized transmission line impedances and lengths. Simulate using ADS and show S11 and S21plots to 5 GHz. Place Marker at 2.4 GHz.(33 pts)

View answer

Question 26686

posted 1 years ago

4. ADS Simulate using Smith Chart showing S11 and S22 parameters between 750 MHz and 1.25 GHz. Place a marker at 1 GHz. Use the S2P component part and use theMRF911D.S2P file copied to the Desktop. The MRF911D.S2P file is found in the Amplifier section of you Blackboard page.
Follow the example in the Amplifier section to give the S parameters in table format, find using the ADS EQUATION the stability factor K, and G max as shown in the example provided in the Amplifier section of your Blackboard page.

View answer

Question 26684

posted 1 years ago

Impedance match a complex load of ZL = 25+ j15 Q to a 50 Q source impedance using a three element L-C matching pi-type network with one series inductor. Remember to perform conjugate matching for maximum power transfer. Determine the component values for operation at 300 MHz. Simulate using ADS and include results of Sl1 and S21plots up to 1 GHz. Place a marker at 500 MHz. (33 pts)

View answer

Question 26685

posted 1 years ago

. The MRF911D transistor with common-emitter S-Parameters for VCE=8V and IC=10 mA
! MRF911D.S2P
! MRF911
! VCE=5V; IC=20mA
# GHz S MA R 50
! S-PARAMETER DATA
\text { So for } 0.5 \mathrm{GHz}, \mathrm{S} 11=0.54 \angle-180, \mathrm{~S} 21=6.4 \angle 85, \mathrm{~S} 12=0.06 \angle 60 \text { , and } \mathrm{S} 22=0.19 \angle-70
Design 1GHZ narrowband amplifier. Use a matching circuit with L's and C's for input andoutput matching to 50 2. (33%)

View answer

Question 26883

posted 1 years ago

Calculate the wavelength of an electromagnetic wave operating at a frequency of 428MHZ.

View answer

Question 26890

posted 1 years ago

A Design a 1 mH toroidal inductor on a Carbonyl W core size T30.Determine the maximum wire size that could be used to realize a single layer winding.

View answer

Question 26885

posted 1 years ago

) Calculate the inductance of a 5 inch length of copper flat ribbon conductor. The dimensions of the ribbon are 0.100 inches in width and 0.002 inches thick.

View answer

Question 26884

posted 1 years ago

Calculate the reactance of the wire from Problem 2 at 10 Hz, 10MHz, and 10 GHz. Create a Linear analysis in ADS and display the wire impedance vs. frequency

View answer

Question 26886

posted 1 years ago

Model a chip resistor (size 0603) with a resistance of 50S in ADS.Consider an application in which 502 impedance must be maintained with +10%. Create a linear analysis and determine the maximum usable frequency of the chip resistor.

View answer

Question 26887

posted 1 years ago

Design an air core inductor with an inductance value of 84 nH. Use a copper wire of 0.050 inch diameter wound on a core diameter or0.100 inch. Determine the number of turns required assuming a tight spaced winding.

View answer

Questions not Found

Most popular subject

Thermodynamics

Essay/Summary

Mechanics

Complex Analysis

Engineering Economics

Calculus

Modern Physics

General Chemistry

Strength Of Materials

Fluid Mechanics

x