Question

Electrical Machines

Match the following according to the type of motor load:

a. Constant power loads

c. Constant torque load

b. Variable torque load

Verified

### Question 45030

Electrical Machines

a) Sketch circuit diagrams showing field connections for the following self-excited generator d.c.generators. In addition connect the following self-excited generator by drawing the properconnections in the two terminal boxes

Read More

### Question 44522

Electrical Machines

A 3 phase STAR wound induction motor is supplied with a line voltage of400V at 60HZ. Each phase of the stator has 300 turns and the rotor is of the wound type with 200 turns. The Rotor windings have a resistance of100 and an inductance of 0.1H.
When the motor is stationary determine each of the following:
i The rotor EMF
ii The rotor frequency
The rotor current
- The power factor of the rotor

Read More

### Question 44521

Electrical Machines

A three phase, 10 pole, delta connected induction motor is supplied at440V, 50 Hz. It draws a current of 32A with a power factor of 0.81lagging. The motor runs at 575 RPM.
Total stator, Rotor copper and mechanical losses equate to 3, 4 and 7%of the input power. Determine each of the following:
The slip
The efficiency of the motor
The torque developed in the rotor
The shaft output torque.
Sketch and label the motor power flow chart for the motor described in this question. You answer must clearly identify the input power, output power and power losses.

Read More

### Question 43379

Electrical Machines

(b) A 1:10 step-up ideal transforner is placed at the output of the generator, and a 10:1step-down ideal transformer is placed at the load end of the transmission line, asshown in Figure (b) below.
\text { (i) What is the new load voltage, } V_{\text {load }} \text { ? }
(ii) What is the ratio of the new load voltage magnitude |Vload to the generated voltage magnitude |Vgl? [1 point]
(iii) What are the transmission power losses Ploss of the system in this case?

Read More

### Question 43378

Electrical Machines

A 2.48-kVms Single-phase generator supplies power to a load through a transmission line.
\text { The load impedance is } Z_{\text {logel }}=100 \angle 36.87^{\circ} \Omega \text {, and the impedance of the transmission line }
\text { is } Z_{\text {int }}=12 \angle 60^{\circ} \Omega \text {. }
If the generator is connected directly to the load as in Figure (a) below:
(i) What is the load voltage-
What is the ratio of the load voltage magnitude |Viond to the generated voltage magnitude |Val? [1 point]
O What are the transmission power losses Ploss of the system? [2

Read More

### Question 43377

Electrical Machines

(b) A two-legged core made of steel is shown below, together with its magnetization curve. The winding (Ni) on the left leg of the core has 600 turns, and the winding (N2)on the right leg of the core has 200 turns. The coils are wound in the directions shown in the figure. The dimensions of the core are as shown, and the currents are i 0.5 Aand i = 1.00 A.
(i) How much total flux dot is produced in the core by the specified currents?
(ii) What is the relative permeability 4, of the core under these conditions?

Read More

### Question 43376

Electrical Machines

(a) The Figure below shows a ferromagnetic core whose mean path length is 40 cm, with a small air-gap of 0.05 cm in length. The cross-sectional area of the core is 12 cm2,and the relative permeability ; of the core is 4000. The coil of the wire on the core has 400 turns. Fringing in the air-gap increases the effective cross-sectional area of the air gap by 5%.
(i) Find the total reluctance of the flux path (core plus air gap). [5 points].
(ii) Find the current, i, required to produce a flux density of 0.5 T in the air-gap.

Read More

### Question 43375

Electrical Machines

\text { A balanced } Y-\Delta \text { system with } V_{a m}=100 \angle 0^{\circ} V_{r m s} \text { positive phase sequence, has a phase }
\text { load impedance } Z_{p}=6-j 12 \Omega \text {, and an impedance } Z_{\text {linc }}=1.0 \Omega \text { in each line. }
(1)Draw the appropriate circuit.
(ii) What is the total input power, Pin, from the source?
(iii) What is the total loss power, Plass, in the lines?
Vhat is the efficiency of the system?

Read More

### Question 43076

Electrical Machines

Propose two methods to control the torque of a D.C motor.Does it will effecting the material and cost? Write it in about30 words.

Read More

### Question 42472

Electrical Machines

8 The manufacturer's data sheet for a 26-kV, 750-MVA, 60-Hz, three-phase synchronous generator indicates that it has a synchronous reactance X, =2.04 and a leakage reactance Xal = 0.18, both in per unit on the base. Calculate (a) the synchronous inductance in mH, (b) the armature leakage inductance in mH, and (c) the armature phase inductance La in m Hand per unit

Read More

### Submit query

Getting answers to your urgent problems is simple. Submit your query in the given box and get answers Instantly.

### Submit a new Query

Success

Assignment is successfully created