Question

Petrochemical Production Technology

1. Determine the collapse pressure regime for 11 3/4", grade K-55 and thickness 0.723 inch.(1.5marks)

2. A vertical separator has ID of 36" and handles liquid of 1500 BPD . Following is the oil and gas data feeding the separator (2.5 marks)

Gas Density: 4.0 lbm/ft³

Sp.g of oil =44Ibm/cubic feet

MW: 20 lb/mol

K factor= 0.32 ft/sec

Gas Molar Volume: 379.5 scf/mole

Calculate the liquid capacity of the separator in (bbl/hour) when retention time is 6 minutes,and liquid volume 22bbl.

Verified

### Question 41320

Petrochemical Production Technology

The following formation resistivity factors were measured on a suite of gas taken from a producing formation. Determine the coefficient a and the exponent m of this equation. Do appropriate plot. [You can use excel to draw the data, then use your ruler to estimate a & m values, also learn how to list the values by hand on a Log-Log scale]
F=a \phi^{-m}

### Question 41319

Petrochemical Production Technology

A consolidated sandstone core sample (d2.1 cm and L = 3.6 cm) is%3|saturated with brine of 0.52 N.m resistivity. The core was desaturated insteps, and the following resistance (N) were measured at each saturation.[You can use excel to draw the data, then use your ruler to estimate the required parameters, also learn how to list the values by hand on a Log-Log scale]
a) Estimate the rock porosityb) Determine the saturation exponent of the rock
b) Determine the saturation exponent, n, of the rock

### Question 41318

Petrochemical Production Technology

1.Resistivity of the rock fully saturated with brine is denoted by thesymbol
2.Water resistivity is denoted by the symbol
3.The resistivity in the flushed zone is denoted by the symbol
4.The shoulder bed resistivity is denoted by the symbol
5.The diameter of invasion is denoted by the symbol

### Question 41317

Petrochemical Production Technology

1. The saturation exponent.
2. The resistivity of the rock when Sw = 40%.
3. Estimate the resistivity index when the water saturation equals 20%.

### Question 38514

Petrochemical Production Technology

A reservoir, with a pattern area of 30 acres, is to be water flooded with a five-spot pattern.The reservoir is 15 ft thick and has a porosity of 0.13 and the initial water saturation is0.38 which is considered immobile. Viscosities of oil and water are 2.3 and 1.1 cp respectively. The residual oil saturation is 0.21. FVF’s for oil and water are assumed to be 1.0. Relative permeability data corresponding to the displacement of oil by water are given in the following equations:
k_{r o}=\left(1-S_{w D}\right)^{242}
k_{n=}=0.78 S_{w D}^{3,8}
where:
S_{w D}=\frac{\left(S_{w}-S_{b w}\right)}{\left(1-S_{o r}-S_{w}\right)}
Assume a pressure drop of 500 psi, K= 0.1 darcy, rw=0.5 ft.
1- Using CGM method and Caudle-Witte approach, predict the performance of the waterflooding.
\text { Plot } N_{p}, W_{i}, W p, q_{t}, q_{o}, q_{w}, f_{w}, \bar{S}_{w}, \text { versus time. }
- At water fractional flow of 0.92, calculate the NPV given the following (OP =40$/STB, WIC=1.08$/STB, WHC = 0.75 \$/STB, DF = 0.09)

### Question 30517

Petrochemical Production Technology

Light Naphtha is fed to an isomerisation unit to generate reformate. The volumetric flow rate of light naphtha is 250 m/h with APl equals 70. Determine the following:
a) The yields of each component in the product.t
b) The composition of the product.
\text { Knowing that: } A P I=\frac{141.5}{S G}-131.5

### Question 30516

Petrochemical Production Technology

A 200 mol/h of heavy naphtha is introduced to catalytic reformer to produce reformate. The composition of the feed as well as the constants (a,b) for the equilibrium constants K are given for each component in feed in the following table:
Determine the composition of the product at T= 550 °C and pressure 15 bar.

### Question 30515

Petrochemical Production Technology

A heavy naphtha is fed to a catalytic reformer at a rate of 271 mol/h. The composition of the heavy naphtha is listed in the following table:
Determine the following:
a) The mole flow for each component in the product of this reformer.
b) The composition of the product from this reformer.

### Question 30514

Petrochemical Production Technology

A heavy naphtha feed is introduced to a catalytic reforming unit to generate a reformate. The volumetric flow rate of the heavy naphtha is 200 m'/h. The heavy naphtha comprises 25 vol%naphthene, 70 vol% Paraffins and the remaining is aromatics. The RON of the reformate is 96.Calculate the yields of each product in this reformer.

### Question 30372

Petrochemical Production Technology

Consider the following simultaneous nonlinear equations:
x^{2}+y+z=6
x^{2}+y^{2}+z^{2}=14
x y z+z=9
Starting from the initial guesses: xo = 1.5, yo = 2.5 and zo = 3.5, perform the following:
a) Determine the roots of the system of equations using the successive substitution method.Perform three complete iteration. Show your calculations.
b) Determine the roots of the system of equations using the Newton-Raphosn method. Perform the computations until & = 7%. Show your calculations.
c) Write a MATLAB script that performs ten iterations of the Newton-Raphson method.
d) Solve the system of equations by calling the function newtmult, with an accuracy of 10 significant figures.Page 1 of 1