- Home
- questions and answers
- for exercises 7 10 find a function that describes the displacement of

Strength Of Materials

For exercises 7-10, find a function that describes the displacement of the mass of the given mass-spring system. Provide a table of values in 1 second intervals for 0 <t< 5. Classify the type of damping as over-damped, under-damped or critically-damped, and if the motion is periodic, find the period and frequency of the oscillations.

Mass 1kg, damping constant 20 , spring constant 100. The mass is displaced 0.5m downward and given an initial velocity of 2 in the downward direction.m

Verified

Strength Of Materials

7-6 Bevel gears transmit torsional, bending, and axial loads to rotating shafts, such as shown in figure13-36. For this problem, the free body diagram for a shaft ABC is shown in the figure, where points Aand C are at the bearings. Line BG is on the bevel gear extended to the shaft center from point G, the contact point with the mating gear. Transmitted from the mating gear are tangential, radial, and axial forces F, = 5000 Ibf, F = 58lbf, and F, = 173 Ibf, respectively. The bearing at C supports the axial thrust load. For the shaft material, Su = 90 kpsi, Sy = 65 kpsi, and has a fully corrected endurance limit of 40kpsi. Let (Kr)a = 2.3, (K)b = 2.0 and (K), t = 1.5 where the subscripts a, b, and t represent axial, bending,and torsion, respectively. The diameter of the shaft ABC is 1.5 inches.

Determine the Design Factor (n:) and then determine the design factor ni without axial loading. How much does axial forces contribute to the design factors?

Read More

Strength Of Materials

7-3 The rotating steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA = 340 N*m. The shaft is machined from steel with Sy = 420 MPa and Sut = 560 MPa. Using a safety factor of 2.5determine the minimum allowable diameter of the 250mm section of the shaft based on a) a static yield analysis using the distortion energy theory and b) a fatigue-failure analysis using Goodman. Assume sharp fillet radii at the bearing shoulders for estimating stress concentration factors.

Read More

Strength Of Materials

7-1 a) A shaft is loaded in bending and torsion such that M, = 70 N*m, T, = 45 N*m, Mm = 55 N*m, andTm = 35 N*m. For the shaft, Su = 700 MPA, and Sy = 560 MPA, and a fully corrected endurance limit of Se= 210 MPA is assumed. Let K = 2.2 and Kg = 1.8. With a design factor of 2.0 determine the minimum acceptable diameter of the shaft using the DE Goodman criteria.

Read More

Strength Of Materials

You have been employed as a Quality Engineer in a company involved in a high-volume production of nails for DIY. After receiving feedback from customers regarding the variation of the length of the nails, it has been decided to run some statistical analysis in order to study the quality and the distribution of the process output. For this purpose the length of a random sample of 100 nails has been measured and organised in Table Q3.

Check the data for outliers and eliminate them if any.

b) Using Chi2 criterion test if the data follows a normal distribution.

Plot a histogram and using data acquired in (b) add empirical and theoretical curves for a visual comparison.

Read More

Strength Of Materials

The torques shown are exerted on pulleys A, B, and C. The diameter of shaft AB is 1.3 in. and that of BC is 1.8 in. Knowing that both shafts are solid, determine the maximum shearing stressin (a) shaft AB, (b) shaft BC.

Read More

Strength Of Materials

Determine the torque T that causes a maximum shearing stress of 70 MPa in the steel cylindrical shaft shown.

Read More

Strength Of Materials

The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A.

Read More

Strength Of Materials

(a) Determine the angle of twist caused by a 40-kip -in.torque T in the 3-in.-diameter solid aluminum shaftshown (G = 3.7 × 10°psi).

(b) Solve part (a), assuming that the solid shaft has been replaced by a hollow shaft of the same outer diameter and a 1-in. inner diameter.

Read More

Strength Of Materials

Knowing that a force P of magnitude 750N is applied to the pedal shown, determine (a) the diameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C.

Read More

Strength Of Materials

Each of the four vertical links has an 8 × 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E.

Read More

Getting answers to your urgent problems is simple. Submit your query in the given box and get answers Instantly.

Success

Assignment is successfully created

2017-2022 TutorBin. All Rights Reserved*The amount will be in form of wallet points that you can redeem to pay upto 10% of the price for any assignment.

**Use of solution provided by us for unfair practice like cheating will result in action from our end which may include permanent termination of the defaulter’s account.Disclaimer:The website contains certain images which are not owned by the company/ website. Such images are used for indicative purposes only and is a third-party content. All credits go to its rightful owner including its copyright owner. It is also clarified that the use of any photograph on the website including the use of any photograph of any educational institute/ university is not intended to suggest any association, relationship, or sponsorship whatsoever between the company and the said educational institute/ university. Any such use is for representative purposes only and all intellectual property rights belong to the respective owners.

**Use of solution provided by us for unfair practice like cheating will result in action from our end which may include permanent termination of the defaulter’s account.Disclaimer:The website contains certain images which are not owned by the company/ website. Such images are used for indicative purposes only and is a third-party content. All credits go to its rightful owner including its copyright owner. It is also clarified that the use of any photograph on the website including the use of any photograph of any educational institute/ university is not intended to suggest any association, relationship, or sponsorship whatsoever between the company and the said educational institute/ university. Any such use is for representative purposes only and all intellectual property rights belong to the respective owners.

Get Homework Help Now!

+

a

+

Success

Assignment is successfully created

Error

Please add files or description to proceed