Section 1 - Investigation of Analogue Circuits Experiment 1: Verification of

Question
Section 1 - Investigation of Analogue Circuits Experiment 1: Verification of Circuit Analysis Methods The purpose of this experiment is to verify the classical circuit analysis approaches, which include the mesh

analysis method and the nodal analysis method, using the LTspice simulator. The circuit diagram is shown in Fig. 1 below. 24 V E₁ 502 ww R₁ R₂802 6 V Rs 3202 Fig. 1 Circuit diagram for Experiment 1 Tasks for Experiment 1: (1) Write the mesh current equations and determine the value and the direction of the mesh currents. Theoretically calculate the current through and the voltage across each resistor. (2) Write the nodal voltage equations and determine the value and the polarity of the nodal voltages. Theoretically calculate the current through and the voltage across each resistor. (3) Build up the circuit in the LTspice simulator and complete the simulation analysis; capture the waveforms of the current through and the voltage across each resistor. (4) Compare the theoretical prediction with the simulation results. Evidence required in your report for the assessment of Experiment 1: Title of your investigation. Description of your investigation (what did you do). • The full working of determining the voltages across and the currents through each resistor, respectively using the mesh analysis and the nodal analysis methods should be presented. You can write down your working on a piece of paper and include the photo of the working in your coursework report. • A circuit diagram built up in the LTspice simulator. Captured waveforms labelled with all relevant parameters. The results obtained using the mesh analysis method, the nodal analysis method and the simulator should agree with each other. If not, please find out the reasons and correct mistakes (if there are any) in your theoretical calculation and/or in the simulation. Full source files are ready for simulation (submitted along with the report). Marking scheme for Experiment 1 [Total 10 marks]: The mesh current equations, and the values and the directions of the mesh currents are correct. [2 marks] • The nodal voltage equations, and the values and the polarities of the nodal voltages are correct. [2 marks] • The value and the direction of the current through each resistor and the value and the polarity of the voltage across each resistor are correct. [2 marks] The circuit is correctly built up in LTspice and the simulation results are correct. [2 marks] • The results obtained using the three methods agree with each other. If not, proper analysis and discussions should be provided. [2 marks]/nExperiment 2: Verification of the Thevenin's Theorem The purpose of this experiment is to verify Thevenin's theorem, using the LTspice simulator. Thevenin's theorem can significantly simplify the analysis of a circuit and thus has been widely used in practice. The most important steps of obtaining the Thevenin's equivalent circuit of an analogue circuit are the determination of the Thevenin's equivalent voltage ETH and the Thevenin's equivalent resistance Rm. This experiment will use the circuit diagram shown in Fig. 2 to verify Thevenin's theorem using the LTspice simulator. 3 V R₁ 19 4V-E₁ R₂40 E₂ 202 ww R₁ Rs 3892 Fig. 2 Circuit diagram for Experiment 2 Tasks for Experiment 2: (1) Determine the Thevenin's equivalent voltage ETH and the Thevenin's equivalent resistance R external to Rs. (2) Draw the Thevenin's equivalent circuit external to Rs. (3) Choose a random resistance value for Rs and theoretically calculate the current through and the voltage across Rs. (4) Using the chosen value of Rs, build up the circuit in the LTspice simulator and measure Ent and RT external to Rs. (5) Capture the waveforms of the current through and the voltage across R₂ (6) Compare the theoretical prediction with the simulation results. Evidence required in your report for the assessment of Experiment 2: Title of your investigation. Rs Description of your investigation (what did you do). • The full working of determining En and RT external to Rs. You can write down your working on a piece of paper and include the photo of your working in the coursework report. • Theoretical prediction of the voltage across and the current through Rs. A circuit diagram built up in the LTspice simulator. Measurements of ETH and Rm in the LTspice simulator. Captured waveforms labelled with all relevant parameters. The simulation results obtained via LTspice should agree with the theoretical prediction. If not, please find out the reasons and correct mistakes (if there any) in your theoretical calculation and/or in the simulation. • Full source files ready for simulation (submitted along with the report). Marking scheme for Experiment 2 [Total 10 marks): • The value and the polarity of En and the value of RT are correctly calculated. [2 marks] • The Thevenin's equivalent circuit is correct and the voltage across and the current through Rs are correct. [2 marks] • The circuit is correctly built up in LTspice. [2 marks] • The value and the polarity of En and the value of Rh are correctly measured via LTspice. [2 marks] discussions [2 marks] • The simulation results agree with the theoretical prediction. If not, proper analysis and should be provided./nExperiment 3: Common-collector Amplifier (Emitter Follower) The purpose of this experiment is to introduce a basic configuration of the emitter follower circuit. Emitter followers are used to buffer signals, which means they are capable of taking a signal from a high impedance source and delivering it to a low impedance load. A properly biased emitter follower circuit, operating from a single positive supply is shown in Fig. 3. In this circuit, the input signal is a 1 kHz sinusoidal wave with an amplitude of 2 V. The purpose of this experiment is to familiarise you with the concept of biasing a transistor so that it is always in its operating region. You should find and read the datasheet of the transistor 2N3904 before building the circuit. VI CI 1p SINE(O 2 IK) 150k 2023-2024 >R₂ 150k Q1 283904 6.3k 1 Load Fig. 3 An emitter follower operating from a single DC voltage supply. Tasks for Experiment 3: 1. In Fig. 3, choose a standard value (greater than 10 k) for the load resistor. 2. Build up the circuit shown in Fig. 3 (including the chosen load resistor) using the LTspice simulator. 3. Obtaining the waveforms of the input and the output voltage signals using the simulator. The input voltage is the voltage across V1 and the output voltage is the voltage across the load. Please compare the input voltage signal with the output voltage signal and find out whether there are any changes in the magnitude and in the phase. 15V 4. Obtaining the waveforms of the input and the output current signals using the simulator. The input current is the current through V1 and the output current is the current through the load. Please compare the input current signal with the output current signal and find out whether there are any changes in the magnitude and in the phase. 5. Determine the voltage gain (the ratio of the peak-to-peak amplitude of the output voltage to the peak- to-peak amplitude of the input voltage) and the current gain (the ratio of the peak-to-peak amplitude of the output current to the peak-to-peak amplitude of the input current) of the circuits. The peak-to- peak amplitude is the difference between the maximum value and the minimum value of a signal. Please note, the phase difference between the output and the input signals should be considered too. Build up the circuit shown in Fig. 3 on a breadboard and measure the waveforms of the input voltage signal and the output voltage signal using an oscilloscope in the lab. 6. 7. Compare voltage gain obtained via the simulator with the one measured in the lab. Evidence required in your report for the assessment of Experiment 3 • Title of your investigation • Description of your investigation (what did you do) • Circuit diagram built in the simulator • Photos of the circuits built for the lab experiments • Captured waveforms via the simulator and in the lab Discussion of results. This must fully explain your findings Full source file ready for simulation (submitted along with the report). Page 4 of 9

Question image 1Question image 2Question image 3