turbomachinery pumps and valves homework help

Boost your journey with 24/7 access to skilled experts, offering unmatched turbomachinery pumps and valves homework help

Trusted by 1.1 M+ Happy Students

4.2Trust Pilot

4.4Edu Reviewer

5App Review

4.5Student

Recently Asked turbomachinery pumps and valves Questions

Expert help when you need it

Q1:Water reaches the wellhead of a single flash geothermal plant at 2.0 MPa, 210°C, and 22.5 kg/s. The water is flashed to 800 kPa. The vapor portion goes through a turbine with an isentropic efficiency of 90% and the condenser pressure is 10 kPa. Both pumps have efficiencies of 68% and the injection well pressure is 4.0 MPa. Determine: a. The power produced by the turbine, in kW b. The total pump power input, in kW. c. The rate of heat input in the earth or "boiler," in kW d. The overall efficiencySee Answer
Q2:1. 2. 3. 4. 5. 6. Describe the basic components and operation of a screw pump. Describe the basic components of a lobe pump. List the typical startup and shutdown procedures for a positive displacement pump. List the typical startup and shutdown procedures for a centrifugal pump. Describe how to startup a dynamic compressor. Describe how to startup a positive displacement compressor?See Answer
Q3:7. What is the equivalent length of the following pipe (200 ft, 2"-sch 40) and fitting and connections? Gate Valve Wide Open 90⁰ Swing Check Valve 45° Globe Valve Half Open 90⁰See Answer
Q4:8. Water is pumped from one storage tank to a higher tank at a steady rate of 1L/s. The difference in the elevations of the two water tanks is 50 m. The storage tank, which serves a source, is open to the atmosphere, while the tank receiving the water has a pressure of 170.3 kPa. The length of the suction piping is 10 m and the length of the discharge piping is 75 m. The power supplied by an electric motor to the pump shaft is 1000 W. All piping is 1-in, schedule-40 steel pipe. Find the pump efficiency.See Answer
Q5:9. Consider the fluid in the tank below. The fluid is fuel oil (u= 8.0 cP, p = 62 lb/ft"), the piping is 10 feet in length, 1% ", sch 40. If the effect of friction is NOT neglected, what is the velocity of the fluid as it exits the pipe? + 20 ftSee Answer
Q6:Using the 6 steps discussed in class, complete the following problem: A pump draws water through a piping arrangement at a mass flow rate of 20 lb/s. At the pipe inlet, the pressure is 14.7 psi, the temperature is 68F, and the water flows at a speed of 10 ft/s. At the pipe exit, the temperature is 68F, the pressure is 20 psi, and the velocity is 40 ft/s. Determine the power required by the pump in hp and Btu/s if the exit is 50 ft above the inlet.See Answer
Q7:1. What is a governor valve? 12 2. Describe the main difference between reaction and impulse steam turbines. What is the function of a steam strainer? Describe how a steam turbine is started up. Identify the main parts of a steam turbine. 3. 4. 5.See Answer
Q8:6. 7. An orifice having a diameter of 1" is used to measure the flowrate of a fluid (S.G. =0.85, viscosity=20 cp) in a horizontal, 2-in, sch 40 pipe at 70 F. The pressure drop is measured by a mercury monometer (SG=13.6), which read 3.0 cm. Calculate the volumetric flowrate of the fluid. An underground pressurized water tank is used to fill an elevated tank at 100 gpm of water. process. The underground tank is 20 feet below the pump with is used to transfer the liquid to the elevated tank 50 feet above the pump and open to the atmosphere. The pump is 10 hP, n=0.9, with a NPSHR of 30 feet. The suction side piping is 35 feet, 3" Schedule-40 carbon steel, the discharge piping is 65 feet, 2" schedule-40 carbon steel. Friction loss through fitting and valves may be disregarded. What is the minimum pressure in Tank 1 that will allow the pump to work without cavitation? 20 2 50 ftSee Answer
Q9:Question 1. [5 marks] A power generation plant is as illustrated in the figure below. On the right (above), thermodynamic data A to Boler Pump Location Leaving boiler Entering turbine Leaving turbine, entering condenser Leaving condenser. entering pump Pump work= 4 kJ/kg Turbine Ⓡ Pressure 2.0 MPa 1.9 MPa 15 kPa 14 kPa b. Turbine work. c. Heat transfer in the condenser. d. Heat transfer in the boiler. Condenser >- given: Temperature or Quality 300°C 290°C 90% 45°C are provided for such a power plant. In addition from the steam tables the following are h1 = 3023.5 kJ/kg h2 = 3002.5 kJ/kg h3 = 226.0+ 0.9(2373.1) = 2361.8 kJ/kg h4 = 188.5 kJ/kg No changes in kinetic or potential energy will be considered in the solution. Calculate the following quantities per kilogram flowing through the unit: a. Heat transfer in the line between the boiler and turbine.See Answer
Q10:Question 2. [5 marks] A coal-burning steam power plant produces a net power of 300 MW with an overall thermal efficiency of 32 percent. The actual gravimetric air-fuel ratio in the furnace is calculated to be 12 kg air/kg fuel. The heating value of the coal is 28,000 kJ/kg. Determine (a) the amount of coal consumed during a 24-hour period and (b) the rate of air flowing through the furnaceSee Answer
Q11:Instructions: write a lab report style for these 10 valves listing just the application and description of these valves. part 1: 1. Gate 2. Check 3. Plug 4. Butterfly 5. Needle part 2: 1. Pinch 2. Plug 3. Control 4. Knife gate 5. Piston please create these following things: - cover page listing the title(choose an appropriate one of your choice) - the references for each part APA 7th style. - add pictures for each valve, and put a figure number for eache on(ex. figure 2.2 Check valve") word limit - 500 wordsSee Answer
Q12:Question I Provide an example of a turbojet engine from the literature and explain the interest of conducting a thermodynamic analysis of such a system for design purpose.See Answer
Q13:Question II Analyze the thermodynamic cycle of a turbojet engine in term of system performance and discuss how the design parameters can affect specific industrial and environmental needs.See Answer
Q14:You need to write difference between Liquid, Solid and Hybrid engines for each of the below listed majors.See Answer
Q15:Part A: Single Pump performance testSee Answer
Q16:Part B: Two pumps connected in series.See Answer
Q17:Part C: Two pumps connected in parallelSee Answer
Q18:1. A pump steadily delivers water through a hose terminated by a nozzle. The exit of the nozzle has a diameter of 2.5 cm and is located 4 m above the pump inlet pipe, which has a diameter of 5.0 cm. The pressure is equal to 1 bar at both the inlet and outlet, and temperature is constant at 20°C. The magnitude of the power input required by the pump is 8.6 kW, and the acceleration of gravity is g=9.81 m/s². Determine the mass flow rate delivered by the pump, in kg/s. See Answer
Q19:2. A solar collector panel with a surface area of 32 ft² receives energy from the sun at a rate of 150 BTU/hr per ft² of collector surface. Thirty-six percent of the incoming energy is lost to the surroundings. The remainder is used to heat liquid water from 110 to 140°F. The water passes through the solar collector with a negligible pressure drop. Neglecting kinetic and potential energy effects, determine (at steady state) the mass flow rate of water, in lb/min. How many gallons of water at 140°F can eight collectors provide in a 30 minutes? See Answer
Q20:3. The electronic components of a computer consume 0.1 kW of electrical power. To prevent overheating, cooling air is supplied by a 25 W fan mounted at the inlet of the electronics enclosure. At steady state, air enters the fan at 20°C, 1 bar and exits the electronics enclosure at 35°C. There is no significant energy transfer by heat from the outer surface of the enclosure to the surroundings and the effects of kinetic and potential energy can be ignored. Determine the volumetric flow rate of the entering air, in m³/s. See Answer

TutorBin Testimonials

I got my Turbomachinery Pumps And Valves homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.

Joey Dip

I found TutorBin Turbomachinery Pumps And Valves homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.

Rick Jordon

TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Turbomachinery Pumps And Valves subject guidance.

Andrea Jacobs

I trust TutorBin for assisting me in completing Turbomachinery Pumps And Valves assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.

Lilian King

Joey Dip

Rick Jordon

Popular Subjects for turbomachinery pumps and valves

You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin turbomachinery pumps and valves homework help.

TutorBin helping students around the globe

TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.