reinforced cement concrete homework help

Boost your journey with 24/7 access to skilled experts, offering unmatched reinforced cement concrete homework help

Trusted by 1.1 M+ Happy Students

4.4Trust Pilot

4.4Edu Reviewer

5App Review

4.8Student

4.2Sitejabber

Recently Asked reinforced cement concrete Questions

Expert help when you need it

Q1: 10. Explain the first area of moment at h/2 and the second area of moment at h for a concrete beam, which is b wide and h deep.See Answer
Q2: 5) (100 points) What are the recommendations for the concrete memo based on the objective and results (i.e., should the mix design be accepted or are changes to the mix design necessary?)See Answer
Q3: 2. (40 pts) The No 7 bottom bars are epoxy coated. If normal weight concrete having astrength of 3,500 psi is used with 60 ksi steel, determine the required development length. Use simplified equations from ACI Table 25.4.2.3 (attached) (20 pts) b. Use equation from ACI 25.4.2.4 (20 pts) See Answer
Q4: 8. What cements would be appropriate for concrete pavement repair under winter conditions?See Answer
Q5: 4. Calculate the compound composition for a Portland cement having the following oxideanalysis: a. C= 64.15%, S = 21.87%, A = 5.35%, F = 3.62%, S= 2.53% b. C= 63.54%, S = 23.09%, A = 3.61%, F = 6.38%, § = 2.29%See Answer
Q6: 2. In 2019, Portland cement consumption in the US was about ? (metric tons), and the cement consumption in the whole world was about ? (metric tons)See Answer
Q7: 3. Calculate the material cost of the concrete for a rectangular parking garage slab with the dimension of 40-feet by 100-feet. The concrete slab's thickness is 6-inch. Assuming the cost of concrete is $140 per cubic yard (yd³).See Answer
Q8: 6. Assign each of the following cements to one of the ASTM Types I to V: a. C:S = 55%, C2S = 21%, C3A = 11%, C4AF = 8%, fineness = 480 m2/kg b. C3S = 55%, C2S = 22%, C3A = 10%, C4AF = 8%, fineness = 380 m²/kg c. C3S = 44%, C2S = 34%, C3A = 4%, C4AF = 13%, fineness = 370 m²/kg%3D d. C3S = 30%, C2S = 45%, C3A = 6%, C4AF = 12%, fineness =320 m² kgSee Answer
Q9: a) Determine the distance, c (which locates the neutral axis from the top of the beam) for the beam section shown below. b) Does the beam satisfy ACI minimum and maximum reinforcement limits? Use fc'=4X00 psi and fy=5X000 psi. See Answer
Q10: Based on a structural analysis, an engineer decides to design the roof beam shown below such that the reinforcement ratio, p will always be 0.01X. Dead load includes beam self-weight.Determine if the design moment capacity (phi)Mn is greater than the factored design moment Mu. Use fc'-4X00 psi and fy 5X000psi See Answer
Q11: 6) (400 points) Type a 1–2-page memo describing the tests and results of the hardenedconcrete tests. Be sure to include the following: a. A clear purpose/objective for the memo. (Hint: Whybeing tested?)are the concrete specimens b. Logical conclusions and recommendations based on the objective. c. Follow the writing resource guidelines. d. ALL tests and results ALL necessary calculations and figures in the appendix. f. Specify if the hardened concrete mix meets the requirements of the design. g. Give recommendations based on lab results.See Answer
Q12: 1) (100 points) Use the test values obtained in lab to calculate the Compressive Strength,Modulus of Rupture, and Splitting Tensile Strength for the concrete. Create a table of the results that will be used in the body of the memo. Format the calculations for use in the attachments of the memo.See Answer
Q13: 3) (100 points) What is the objective/purpose of the concrete memo?See Answer
Q14: 2) (100 points) What are requirements for the hardened concrete?engineering equations and the mix strength design.) Did the mix meet the requirements?(Hint: use theSee Answer
Q15: 4) (100 points) What tests were performed to meet this objective?See Answer
Q16: The attached worksheet was obtained in a laboratory design of asphalt concrete mixture for medium traffic. Carry out the required analysis and hence complete the table. Using the average results for each asphalt content, plot the necessary graphs and determine the optimum asphalt content based on air voids content requirement. Verify whether the optimum asphalt content determined will meet the GHA dense-graded specifications for medium traffic given in the table below. Use the following specific gravity values for your analysis: Bulk specific gravity of aggregates, Ga=2.65, Specific gravity of bitumen (asphalt), Gs=1.02 You should show sample computations involved in your analysis. Marks will be awarded forclarity of DEssentation. Average values of parameters are not required in shaded regions on the laboratory worksheettable for Q but are required in the areas with a tick (V) for all asphalt contents. See Answer
Q17: 4.9. Determine the nominal moment capacity of the section in Fig. 4. la using the reinforcement areas from Problem 4.1. f, = 60,000 psi.See Answer
Q18:data sheet for Hardened concrete lab Concrete compressive strength (ASTM C39): Name of CylinderSee Answer
Q19:Evaluation of Corrosion Cracks Induced by Accelerated Corrosion Technique for 1 Cylinder Cement= 2.08kg Course aggregate = 5.924kg fine aggregate = 4.1184 kg Water = 1.144 kg salt=46.8 g fiber glass =26 gSee Answer
Q20:Consider a rectangular section with a height of 20" and a width of 12". The strain distribution on this section features a strain of 0.0015 at the top of the height and a strain of -0.0010 at the bottom of the height. This section is made out of a linear elastic material with a modulus of elasticity equal to 12,000 ksi. Determine the effective axial load and moment acting about the gross centroidal axis and the curvature of the section.See Answer

TutorBin Testimonials

I found TutorBin Reinforced Cement Concrete homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.

Rick Jordon

TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Reinforced Cement Concrete subject guidance.

Andrea Jacobs

I trust TutorBin for assisting me in completing Reinforced Cement Concrete assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.

Lilian King

I got my Reinforced Cement Concrete homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.

Joey Dip

Popular Subjects for reinforced cement concrete

You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin reinforced cement concrete homework help.

TutorBin helping students around the globe

TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.