Instructions: 1) The assignment maximum mark is 20, and it worth 10% of the course overall mark. 2) Assignment shall be submitted through the Assignment Section of the course on the blackboard. Note that there is only ONE attempt available for the assignment submission. Please completely check your work before submission. 3) Assignment is due on Wednesday Oct 18, 2023 at 11:59 PM. 4) Late submission of the assignment has a penalty of two marks per calendar day. Submission Requirements: •The assignment shall be submitted as one pdf file including the cover page, plan of network, all output tables for nodes and links. • The Cover Page shall reflect the course name and code (i.e. CIVL3087), the assignment name, due date, your full name and student number, and your professor's name. .Read the assignment work information carefully (attached pages). • Detailed output, calculations if require, explanations, showing units, neat drawing, are the minimum requirements of the assignment. • Every item of the requirements has a portion of the total mark. Make sure to respond all the requirements and provide a complete package. The original provided drawings for WM assignment Work Information pages must be attached to your submission. . • Professional presentation of your work is very important. Computerised output is preferred. 10% of the total mark is for submission of a clean, legible, and organised assignment. part 1-WM design 1) Draw a WM network plan(choose from proj#1-plans-folder) by software. 2) Review the provided drawings of the project and make yourself familiar with their details. 3) Read/find the information you need for the assignment calculations and design, on the provided drawings; example length(Based on the scale), and demand for each joints based on population.(Recommended: Choose EL=100m for all joints, L=100m and C=100 for all pipes and 2 Lps for random joints) 4) Determine the proper size/diameter of the proposed WM pipes. 5) Print all relevant hydraulic output from software- example: velocity, pressure, Diameter, 6) TIP: Review the examples practiced in the quick start tutorial. 7) Confirm whether the provided diameters of the proposed WM pipe are acceptable (i.e. explain why/how). 8) Confirm whether a smaller size of the WM pipe sections (i.e. one size smaller) are acceptable. For this item, you should redo your RUN based on the new/revised sizes, consider about total head, pressure... 9) The min pressure of network is 1A minutes and C=100(Hazen-Williams). (If someone add a reservoir to the system, without pump, the total head should be 100+ 1A)-Remember the RANGE between min and max of joint's pressure never be more than 30m(200kpa)). 10)Add a pump station, or more reservoir to the system if necessary. "Use the first right side digit of your student number as "A". Example: if your student number is 1234567890, the min pressure of 1A will be 10 m.

Solved: Instructions: 1) The assignment maximum mark is 20, and it worth 10% o

Home
questions and answers
instructions 1 the assignment maximum mark is 20 and it worth 10 of th

Question

Instructions: 1) The assignment maximum mark is 20, and it worth 10% of the course overall mark. 2) Assignment shall be submitted through the Assignment Section of the course on the blackboard. Note that there is only ONE attempt available for the assignment submission. Please completely check your work before submissi

This question hasn’t solved by tutor

Solution unavailable? No problem! Generate answers instantly with our AI tool, or receive a tailored solution from our expert tutors.

Found 10 similar results for your question:

Q1. Calculate capillary rise/fall in a glass tube 2 mm diameter when immersed in (a) water (b) mercury.Both the liquids are at 20°C and the surface tension values at this temperature for water and mercury are 0.072 N/m and 0.052 N/m respectively. The specific gravity of mercury is 13.6. The contact angle of water and mercury are 0° and 130° respectively.

1. A pump-around reflux is an internal reflux for a distillation column where the liquid is withdrawn from a lower tray, cooled in a heat exchanger resulting in heat recovery and then sent back to an upper tray thus reducing the amount of top reflux. In a given distillation tower, the pump-around reflux is withdrawn from the 20th tray and sent to a pump on the ground which is located 20 m below the 20th tray. The pump discharge is cooled in a heat exchanger, and then returned to the 16th tray at the tray level through a control valve. The pump discharge line (including equivalent length of all fittings, bends,etc.) is 50 m long. For a nominal flowrate of 120 m²/h, pressure drop in the cooler is 20 kPa. Assume turbulent flow conditions. Neglect suction line frictional pressure drop. Following information is available:Tray spacing: 0.5 m, Pressure drop per tray: 1 kPa, Discharge pipe diameter = 0.3 m and f (friction factor) = 0.04, Density of Liquid (assume that it is constant) = 800 kg/m³, Tower top pressure: 300 kPa, Pump curve for the pump-around reflux pump is given by: APрump(kPa)=300 – 5v^2 where v is flowrate in m³/min a. For a 50% scale up in the pump-around reflux flow, what would be the minimum discharge pressure of the pump (i.e., under the condition when the pressure drop inа.the control valve is zero)? b. What is the pressure drop in the control valve for the 50% scale up case?

.The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600rpm and is supported in rolling bearings at A and B. The applied forces are F1 = 2500 Ibf andF2 = 1000 lbf. Determine the minimum fatigue factor of safety based on achieving infinite life.If infinite life is not predicted, estimate the number of cycles to failure. Also check for yielding.

The cylindrical tank with hemispherical ends shown in Fig. P2.46 contains a volatile liquid and its vapor. The liquid density is 800 kg/m3,and its vapor density is negligible. The pressure in the vapor is 120 kPa (abs) and the atmospheric pressure is 101 kPa (abs).Determine: (a) the gage pressure reading on the pressure gage, and (b) the height, h, of the mercury, manometer.

Two cables are tied together at C and are loaded as shown. Knowing that P = 500 N and a =determine the tension in (a) in cable AC, (b) in cable BC.60°, N= T_{A}= 3) The tension in the cable BC is \mathrm{T}_{\mathrm{B}}=

1. Classify each of the structures as statically determinate, statically indeterminate, stable, or unstable. If indeterminate, specify the degree of indeterminacy. (22 pts.)

12-113. The position of a particle is defined by r ={4(t – sin t)i + (2t^2 – 3)j} m, where t is in seconds and the argument for the sine is in radians. Determine the speed of the particle and its normal and tangential components of acceleration when t=1 s.

A 100 ft steel tape standardized at 68 °F and supported throughout under a tension of 10 Ibs was found to be 100.2 ft long. The tape had a cross sectional area of 0.009 in? and a weight of 0.03 Ib/ft. The tape is used to measure a horizontal distance (AB) and the measured length comes out to be 300 ft. CALTRANS plans a new ramp to connect Nutwood with US57. The ramp starts from point A (on Nutwood) to C (on US57) wherein point C will be vertically above point B (a current point on Nutwood that will get buried by ramp). The must have a smooth 4% grade, thus the tape will be used fully supported. Determine the correct slope distance to be measured (i.e. length AC) if a pull of 15 Ibs is used and the temperature is 96 °F.

Problem 2: In a boat race, boat A is leading boat B by 50 m and both boats are traveling at a constant speed of 180 km/h. At t = 0, the boats accelerate at constant rates.Knowing that when B passes A, t = 8 s and va = 225 km/h,determine (a) the acceleration of A, (b) the acceleration of В.

1-90 A hydraulic lift is to be used to lift a 1900-kg weight by putting a weight of 25 kg on a piston with a diameter of 10 cm.Determine the diameter of the piston on which the weight is to be placed.